1. MEDIUM VOLTAGE POWER CABLE JOINTS
   
   

   The Power Cable Joints are highly reliable, factory-molded and tested cable joints for 15kV, 25kV and 35(36) kV class distribution systems. When assembled, they provide permanent, fully shielded, fully submersible cable joints for direct burial or vault applications of solid dielectric single-core and three-core cables.

   The Power Cable Joints are designed to meet or exceed the IEC 60502-4 standard as well as the rigid IEEE 404 standard.

    The Power Cable joints offer the benefits of an optimum design for electrical stress control, they are factory molded for consistent high quality and are factory tested before field installation to insure maximum reliability . they are easy to install without special tools and they are easy to specify for various cable types.
   
   

2. HIGH VOLTAGE POWER CABLE JOINTS
   
   
   • Faster installation, as the molding is done in the factory reducing on-site time. No penciling of cable insulation required.
   • Reduced training requirements, easily learned installation procedure.
   • No costly installation Machinery required, field molds or wrapping machines are not required. A low-cost assembly tool is available.
   • No special environment equipment requirements.
   • Unlimited shelf life allows for instant availability.
   • Factory molded quality You can be sure each cable joint in the field is produced exactly per design. Each unit is molded a micro – processor-controlled screw injection press to produce a level of quality not possible with field molding equipment or tape.
   • Factory -100% factory tested each unit is electrically tested in the factory to insure consistent quality.

1. Medium Voltage Modular Termination
   
   Pre-molded Cable Termination for XLPE, EPR and any Polymeric Insulation Cable up to 52 kV Indoor & Outdoor.
   
   
2. High Voltage Transmission Termination
   
   
   • The 69 TCT Termination is lightweight and easy to handle. It can be assembled horizontally on the ground and then raised to the installation position without a crane. Installation can be accomplished without special training using a normal assembly / tension device.
   • The 69 TCT can utilize standard cable support systems.
   • The 69 TCT Termination provides a termination for cable systems rated up to 72.5kv class.
   • It conforms to IEC 60840. This terminator for is designed for solid dielectric cables with insulation diameters from 37 mm to 84 mm.
   • Various lugs are available for the conductor connection.
   • The durable elastomer construction eliminates glaze damage failures associated with porcelain.
   • A state of the art shed design ensures a non-continuous drip path and the non – tracking polymer requires surface oil or grease.

SEPT 72 outdoor sealing end porcelain termination for cable systems with rated voltage up to 72.5 kV.

• The SEPT 72 conforms and type tested according to IEC 60840
• Pre-molded stress control system made of EPDM rubber.
• Termination’s stress cone covers cable cross section area up to 2000 mm2 with diameter over insulation up to 97 mm.
• Termination is filled with an insulating compound up to a level where the electric field is substantially reduced. The terminations base plates and the cables metallic screen are electrically insulated from the supporting structure by means of stand off insulators, designed to withstand both mechanical and electrical operating stresses.
• Termination designed for operation under severe outdoor conditions.
• Main components of the termination are the porcelain hollow insulator, upper metal cap, top bolt, metal base plate, supporting insulators, silicon oil filling compound, O-ring gaskets and pre-molded stress cone for electrical field control.
• Arcing horn, corona ring, overhead clamps are available under customer request, and to be ordered separately.

• L-Shape Elbow 156 LR
  
  156LR Elbow Connector is a fully-rated 15/25kV, 250Amp Class dead break connector. Units include provisions for de-energized operation using standard hot stick tools. It has a standard interface for connecting to 15/25kV, 250 Amp deadbreak bushing inserts, junctions and other accessories. The 156LR is equipped with an integral voltage test point. Mates with bushing interface conforms to CENELEC EN 50181 interface (A).

• T-Shape Elbow 
  
  The T - body is designed to provide fully-shielded, dead-front submersible cable connections to high-voltage apparatus. It can be used through 36 kV with conductor range up to 630 mm2 for aluminum and copper conductors.

• L-Shape Elbow 400LB
  
  The K400LB is designed to provide fully-shielded, dead-front submersible cable connections to high-voltage apparatus. The K400LB can be used up to 25 kV for aluminum and copper conductors.

Link Box is electrically and mechanically one of the integral accessories of HV underground and above ground cable bonding system, associated with HV XLPE power cable systems. we offer an array of its product disconnecting link boxes to complete the desired sheath grounding arrangement. We provide a sealed dry environment for cable metal sheath earthing connections(links). These links may be removed to facilitate cable sheath inspection and testing.

• Cable Breakouts
  
  Cable breakouts are designed for cable sealing crutches and to provide resistance to abrasion, weathering and chemical attack. It’s applicable for indoor and outdoor applications for all types of polymeric and paper insulated cables.
  
  

• Boots
  
  Heat shrinkable stabilized cross-linked Polyolefin anti tracking boots, in red or grey color, designed to provide protection to the end cables and bushing insulation and sealing against ingress of moisture and contamination. and provide insulation and resistance to abrasion, weathering and chemical attack.
  
  

• End Caps
  
  Heat shrinkable stabilized cross-linked polyolefin sealing caps (SC), in black color are ideal for protecting cable ends. SC are designed to seal the end of cables against ingress of moisture and contamination, and provide insulation and resistance to abrasion, weathering and chemical attack. Such sealing caps are required for cable transport, storage and installation.
  
  

• Heat Shrink Tubes
  
  SHSI is an excellent product for sealing and insulating cable splices connections, terminations and jacket repairs. The tubing is designed to withstand the severe mechanical requirements of submersible, and direct buried installations.
  
  

• Low Voltage Heat Shrink Joint
  
  SHSJ (cable Joint) are outstandingly suitable for jointing two single or multi-core, polymeric (XLPE, PVC …), Al or Cu, armored or non-armored in the low voltage range (up to 1kV).
  
  

• Low Voltage Heat Shrink Termination
  
  SHST (cable-Termination) are outstandingly suitable for Terminating multi-core, polymeric (XLPE, PVC …) and power cables, Al or Cu, armored or non-armored in the low voltage range (up to 1kV).

TUBULAR COPPER CONNECTORS FOR MV JOINTS

TUBULAR COPPER CONNECTORS FOR LV JOINTS

TUBULAR COPPER LUGS FOR LV & MV TERMINATIONS

STANDARD COPPER CONNECTORS

STANDARD COPPER LUGS

TUBULAR ALUMINUM CONNECTORS FOR MV JOINTS

TUBULAR ALUMINUM CONNECTORS FOR LV JOINTS

TUBULAR ALUMINUM LUGS FOR MV TERMINATION

TUBULAR ALUMINUM LUGS FOR LV TERMINATION

BI-METALLIC INSERT LUGS FOR MV TERMINATIONS

BI-METALLIC INSERT LUGS FOR LV TERMINATION

BI-METALLIC FRICTION LUGS FOR MV TERMINATION

BI-METALLIC FRICTION LUGS FOR LV TERMINATION